彩鋼板廣泛用于建筑，家電和交通運輸?shù)刃袠I(yè)，對于建筑業主要用于鋼結構廠房、機場、車間，活動房，箱房，凈化車間，庫房和冷凍等工業及商業建筑的屋頂墻面和門等，民用建筑采用彩鋼板的較少。彩鋼板的安裝很有技術性的，沒有經驗的公司根本不知道怎么安裝彩鋼板才能達到要求，這里濟南彩鋼板就根據多年施工老師的經驗，為大家簡單的介紹一下彩鋼板的安裝要求，希望對各位有所幫助。

Color steel plate is widely used in construction, home appliances, transportation and other industries. For the construction industry, it is mainly used in steel structure workshop, airport, workshop, activity room, box room, purification workshop, warehouse, freezing and other industrial and commercial buildings, such as roof walls and doors, while less color steel plate is used in civil buildings. The installation of color steel plate is very technical. Companies without experience don't know how to install color steel plate to meet the requirements. Here Jinan color steel introduces the installation requirements of color steel plate according to the experience of many years of construction teachers, hoping to help you.

彩鋼板安裝要求：

Installation requirements of color steel plate:

一、場地核實

1、 Site verification

1.在潔凈地面上初次處理之后，設備定位。按設備定位、設計圖紙對隔墻放線定位，確定現場尺寸是否與圖紙尺寸、設備位置有相沖突的地方；

1. After the first treatment on the clean ground, the equipment should be positioned. According to the equipment positioning and design drawings, set out and position the partition wall to determine whether the site size conflicts with the drawing size and equipment location;

   
   

2.對現場地面的水平進行核實，看波動是否較大，是否有必要對彩鋼板墻體底部整體校平。

2. Verify the level of the ground to see if the fluctuation is large, and whether it is necessary to level the bottom of the color steel plate wall as a whole.

二、安裝要求

2、 Installation requirements

1.內外圓弧固定：與彩鋼板連接一定要嚴實，外圓弧立柱不駁接，內圓弧連接點之間不錯位，縫隙嚴實。

1. Internal and external arc fixation: the connection with color steel plate must be tight, the external arc column shall not be connected, the internal arc connection points shall not be dislocated, and the gap shall be tight.

2.每一塊頂板與圍護板之間的固定一定有3顆鉆尾螺絲，圍護板、立板之間連接處上下各有一顆拉釘固定，邊施工邊固定，板縫一定垂直；

2. There must be three tail drilling screws between each roof and the enclosure, and a pull screw at the upper and lower joints between the enclosure and the vertical plate. The plate joints must be vertical while the construction is in progress;

3.T型吊梁固定：吊碼沿放線位置定位，間距不超過1.20m，T型梁與連接彩鋼板固定時一定用角鋁或角鐵壓緊，不得留有空隙，壓固體一定在兩塊彩鋼板連接縫之上；

3. Fixation of T-shaped lifting beam: the lifting code shall be positioned along the setting out position, and the spacing shall not exceed 1.20m. When fixing the T-shaped beam and the connecting color steel plate, the angle aluminum or angle iron must be used to compress the T-shaped beam, and no gap shall be left. The pressing solid must be on the joint of two color steel plates;

4.槽鋁固定：固定槽鋁前一定先放線定位，偏差不能超過5mm，槽鋁用M5x30抽心鋁拉釘固定，間接不超過300mm，有門洞位置須設置雙拉釘，間隔不超過50mm；

4. Fixing of channel aluminum: before fixing the channel aluminum, the setting out and positioning must be carried out, and the deviation shall not exceed 5mm. The channel aluminum shall be fixed with m5x30 core pulling aluminum nail, and the indirect distance shall not exceed 300 mm. Double pulling nails shall be set at the position with door opening, and the interval shall not exceed 50 mm;

5.風口安裝：天花上的風口安裝要按圖紙施工，避開T型梁。墻體上的排、回風口安裝要離地200mm；

5. Installation of air outlet: the installation of air outlet on the ceiling shall be carried out according to the drawing, avoiding T-beam. The air outlet and return outlet on the wall shall be installed 200 mm above the ground;

6.外觀要求：整體安裝需平直美觀，不得有碰撞刮劃痕跡，要到才能撕保護膜，板縫連接平實，板縫間距3-4mm，打膠要滿縫平直，不得有縫隙；

6. Appearance requirements: the overall installation shall be straight and beautiful, without collision and scratch marks, the protective film can be torn only after reaching the surface, the plate seam connection shall be smooth, the plate seam spacing shall be 3-4mm, and the gluing shall be full seam and straight, without gaps;

7.門窗安裝：門窗的安裝位置和開啟方向按圖紙要求而定，單開門盡量在同一塊彩鋼板上，雙 開門的中 心線盡量在板縫連接處，以便切下的彩鋼板做門板，門窗的型材連接需嚴密，不能有縫隙，整體門拐留置尺寸一定統一；

7. Installation of doors and windows: the installation position and opening direction of doors and windows shall be determined according to the requirements of the drawing. The single door shall be on the same color steel plate as far as possible, and the center line of double door shall be at the joint of plate seam as far as possible, so that the cut color steel plate can be used as the door plate. The profile connection of doors and windows shall be tight without gaps, and the overall size of the door shall be uniform;

以上是濟南彩鋼板給大家整理的彩鋼板安裝要求和規范，無論是場地還是安裝時的一些注意事項都給大家整理出來了，想要了解更多精彩內容可以直接關注http://www.liondatech.com

The above are the installation requirements and specifications of Jinan color steel plate, and some precautions of both site and installation are sorted out. If you want to know more wonderful content, you can pay attention to it directly http://www.liondatech.com